liquitec
DE EN
Enquiry

bio-plus®

Magnetic Separators ILM and ILM-F

Magnetic separators for hygienic and sterile process lines: the tubular separator reliably removes magnetic solids from the liquid. The ILM-F additionally has a filter basket.

bio-plus® Inline Filter and Magnetic SeparatorPDF · 354 KB · DE/EN
8 / 40bar nominal pressure, depending on closure
DN25…100nominal size, DIN, ISO and OD acc. DIN11866
160°C, CIP and SIP capable, higher on request
Ra < 0.6µm, product contact electropolished

Overview

Magnetic solids stay on the rod.

The separator sits directly in the pipeline and allows a high flow rate with low pressure loss in continuous operation. Cleaning, checking and maintaining the magnetic rod is easy and safe.

  • For liquids carrying magnetic solids
  • Pull only the magnetic rod: the casing stays installed and is cleaned by CIP
  • Or remove the complete inner part and clean it by hand
  • Sterile design, static seals only
  • CIP and SIP capable up to 160 °C
  • Connections bio-plus® sterile union, DIN11864, DIN32676, EN1092
  • Product-contact surfaces electropolished, Ra < 0.6 µm
  • Gaskets FDA conform, USP Class VI, TSE-free
  • Options: feedback unit M12, heating or cooling jacket

Versions

With magnet alone or with filter basket.

magnetic rod in a casingMagnetic Separator ILM

The solids adhere to the casing. They are removed and cleaned with the complete inner part, or only the magnetic rod comes out and the casing is cleaned by CIP while installed.

magnet and filter in oneMagnetic Separator with Filter Basket ILM-F

A magnetic separator is additionally fitted in the filter tube. If the filter basket clogs, it is removed and cleaned by hand. An additional casing tube allows the separator to be cleaned safely and quickly without the magnets fitted.

Technical data

Materials, pressures, temperatures.

Nominal sizes
DN25 to DN100, pipe standards DIN, ISO and OD acc. DIN11866
Nominal pressure
8 bar with screw union or clamp closure, 40 bar with flange closure
Product-contact materials
Housing 1.4435 or 1.4404 (both 316L); special materials such as 2.4602, titanium or 1.4539
Gaskets
EPDM, VMQ (silicone), FKM, FEP-silicone, FFKM
Temperature by gasket
EPDM −40 to +150 °C, briefly 160 °C; VMQ −50 to +200 °C, briefly 230 °C; FFKM −15 to +260 °C
Inside surface
Ra 0.8, 0.6 or 0.4 µm, electropolished or blank
Connections
Weld end DIN11866, bio-plus® sterile union s/f/c, DIN11864-1/2/3, clamp DIN32676, flange EN1092, special connections
Filter basket (ILM-F)
Perforated tube, slot tube or mesh, each with or without seal
Options
Feedback unit M12 with initiator and 10 m cable; heating or cooling jacket
Certificates
Inspection certificate 3.1 for product-contact parts, certification of surface roughness and delta ferrite content, FDA compliance of product-contact gaskets
Traceability
Via the order number

Ordering key

Eleven positions, one version.

Device and size

  • Article: ILM or ILM-F
  • Pipe standard: DIN, ISO or OD
  • Nominal size DN25 to DN100
  • Nominal pressure 8 or 40 bar

Connection and material

  • Housing closure: screw union, clamp or flange
  • Product connection: weld end, bio-plus®, DIN11864, DIN32676, EN1092
  • Material 1.4404 or 1.4435 (both 316L)
  • Gasket EPDM, VMQ, FKM, FEP-silicone, FFKM

Equipment

  • Inside surface Ra 0.8, 0.6 or 0.4 µm
  • Electropolished or blank
  • Filter basket on the ILM-F: perforation, slot or mesh
  • Feedback unit M12
  • Heating or cooling jacket

Contact

Enquiry

Tell us the medium, nominal size, connection, material and gasket, and for the ILM-F the perforation, slot width or mesh width of the filter basket. We will propose the right version.

Prefer to write directly?

+41 55 450 83 00 sales@liquitec.ch